manualshive.com logo in svg

Eaton LMS, Руководство по установке, Страница: 22 / 202

Поделиться
Скачать
Eaton LMS Скачать руководство пользователя страница 22

85360 

Bench mounted 

Jibs 

may be installed on maple bench 

tops or laminate particle board tops. 
  

IMPORTANT

:  

- Maximum Jib loading is 20 lbs. 
- Thru Bolts with Washers (not provided) are required 
  to attach the 

Mounting Plate 

to any bench top less 

  than 1.18” thick.    
  

Tools Required

: 

     -Electric drill 
     -.185” dia. (#13) drill bit 
     -7/16” wrench 
     -9/16” wrench 
  
1. Position the Mounting Plate assembly in the desired 
    location on the workbench and mark the location of 
    the four mounting holes. See 

Figure 3

. 

  
2. Drill four .185” dia. thru holes and fasten the Mount- 
    ing Plate assembly to the top using the 1/4” x  1-1/2”  
    Lag screws and washers (provided). See 

Figure 3

. If   

    the top is less than 1.18” thick, use thru bolts, nuts  
    and washers (not provided).            
  
3. Loosen the clamp bar inside the Mounting Plate as- 
    sembly, insert the 

Vertical Column

 and then tighten 

    the clamp bar. See 

Figure 4

.  

  
4. Insert the 

Jib Assembly

 into the top of the Vertical 

    Column and position it at the desired vertical height. 
    Lock it into place by securely tightening the 3/8”-16 
    bolts and then install the 

End Cap

. See 

Figure 4

.

 

  
 

Mounting plate 
assembly 

Figure 3 

1/4” x 1-1/2” 
Lag screw 

Washer 

Figure 4 

End cap 

Vertical column 

Swinging jib 

Clamp bar 

Mounting plate 
assembly 

3/8”-16 Bolts 

Bench Mounted Jib 

BENCH MOUNTED JIB INSTALLATION

 

  

T o o l   T r a c k / T o o l   J i b  
( c o n t . )  

 
 

  

technical furniture 

A-19 

Содержание LMS











































































































































































































Отзывы:

Нет отзывов