manualshive.com logo in svg

Eaton LMS, Руководство по установке, Страница: 81 / 202

Поделиться
Скачать
Eaton LMS Скачать руководство пользователя страница 81

-1- 

Tools Required

 

     -Phillips head screwdriver 
     -Plastic mallet  

Heavy Duty Shelf Supports

 may be installed with 

Tower, Electronics and General purpose shelves 
to increase their load capacity. 
  

NOTE

: Two people are required for installation 

of the larger shelf sizes; i.e. 48” (1219mm) and 
larger. 
  
1. Install the shelf in the desired location  follow- 
    ing the instructions in the previous sections.

 DO

  

    

NOT 

tighten the six screws which fasten the shelf  

    to the end panels at this time. See 

Figure 1

. 

 
    

NOTE

: If the Shelf Supports are being installed 

    on a pre-installed shelf, unload the shelf and  
    loosen the six screws which fasten it to the end 
    panels. 
  
    When using the Heavy Duty Shelf Supports, the  
    minimum distance that a shelf can be located to 
    the floor is 6.65”. 
  
2. Mark the location of the two trapeziod slots in 
    the slotted standard(s) directly below the shelf. 
    See 

Figure 2

. 

 
3. Remove the shelf from the end panels and in- 
    stall the Shelf Supports by inserting the top  
    pair of hooks into the marked slots in the slot- 
    ted standard and push down. To assure the hooks 
    are seated, tap the top rear of the Shelf Support 
    with a plastic mallet or equivalent. See 

Figure 3

. 

  
4. With two people, re-install the shelf. Carefully  
    position the shelf over the screws on the end 
    panels . Drop the shelf in place and tighten the 
    screws. 
 

Figure 2 

Slotted standard 

Bottom of shelf 

Mark slots 

 

Heavy Duty Shelf Support 
       Part No. 8161X 

82000 

H e a v y   D u t y   S h e l f  
S u p p o r t  

 
 

  

technical furniture 

Figure 1 

Slotted standard 

End panel 

Shelf supports 

Shelf 

Screws 

End panel 

Figure 3 

Marked slots 

Slotted standard 

Hooks 

Shelf support 

F-11 

Содержание LMS











































































































































































































Отзывы:

Нет отзывов