manualshive.com logo in svg

Eaton LMS, Руководство по установке, Страница: 197 / 202

Поделиться
Скачать
Eaton LMS Скачать руководство пользователя страница 197

WARNING

: Electro static discharge can be dangerous 

to equipment and to persons if not properly dissipated. 
Read this supplement thoroughly for information on 
grounding precautions as well as general care and main- 
tenance. 
  
It is recommended that the 

ESD Top

 be grounded by a  

certified electrician and tested before it is used. It is  
important to insure a proper ground to minimize the 
possibility of damage to equipment and person. 
  

ESD GROUNDING 
  

1. The point of ground for the ESD Top is installed at 
    the factory. A 

Ground Wire 

should be attached to 

    the 

Grounding Bolt 

with the other end attached to 

    to the facility electrical ground. See 

Figure 1

. 

  
2. Each ESD Worksurface and Shelf comes with only 
    one grounding point. Surfaces should be connected 
    to ground in parallel and should not be connected to 
    each other in series. 
  
    When tightening the nut onto the Grounding Bolt,  
    

DO NOT OVER TIGHTEN

. Hand t 1/4  

    turn. 
  
3. Once the ESD ground is established, it is important 
    to test the system. Periodic checks of the system are 
    recommened to ensure the integrity of the system. 
    Monitoring devices may be used to alert persons when 
    the integrity of the system has been compromised. 
  
4. Enviromental factors, especially temperature and 
    humidity, have a drastic effect on the resistive pro- 
    perties of the ESD Worksurfaces. 
  

CARE AND MAINTENANCE

 

  
1. When cleaning the surface becomes  necessary, it is 
    important to use non-abrasive cleaners only. If the 
    surface is stained, baking soda and water may be used  
    to remove the stain but excessive scrubbing may  
    damage the surface.  
  
2. It is important that no film or residue be left on the  
    surface of the ESD Top. Failure to thoroughly clean 
    the surface will reduce the dissapative properties of 
    the laminate. 
 

Figure 2 

Improper grounding arrangement 

Proper grounding arrangement 

Figure 1 

Ground point for 
ESD tops 

12 GA Ground wire 

Top of ESD worksurface 

Grounding bolt 

E S D   L a m i n a t e  
 

 
 

  

technical furniture 

esdinstr 

R-1 

Содержание LMS











































































































































































































Отзывы:

Нет отзывов