Taiden hcs-8300 Installation And Operation Manual Download Page 2

Page: 2 / 255

Remark:



Contents may change without prior announcement



All technical specifications are guideline data and not guaranteed features



Taiden Co., Ltd. is not responsible for any damage caused by improper use of this manual



The equipment must be connected to earth!



This product conforms to the rules of the European directive 2004/108/EC.



To protect your hearing, avoid high pressure level on earphones. Adjust to a lower and convenient level.



If any detailed information is needed, please contact your local agent or

TAIDEN

service center in your region.

Any feedback, advice and suggestion about the products is appreciated.



TAIDEN

CongressMatrix

、

mMediaCongress

are the registered trademarks of

TAIDEN

Co., Ltd.



CobraNet is the registered trademark of Cirrus Logic, Inc.



Dante is the registered trademark of Audinate Pty Ltd.



In order to extend the life time of the whole system, we strongly recommend that the congress system

be scheduled to shut down every day in the evening when not in use.

Summary of Contents for hcs-8300
































































































































































































































































Search results

Summary of Contents for hcs-8300

Reviews:

Related manuals for hcs-8300

Brands by name

Popular brands

Taiden hcs-8300, Installation And Operation Manual

Search results

Summary of Contents for hcs-8300

Reviews:

Related manuals for hcs-8300

Brands by name

Popular brands