Taiden hcs-8300 Installation And Operation Manual Download Page 204

Page: 204 / 255

191

2.Setup

After connection of the power supply to the touch panel,

press power button at the right side of the touch panel to

start touch panel; press power button again to close

touch panel. When touch panel on, hold pressing power

button for 6 seconds, system setup interface will prompt.

You should input password to enter system setup

interface. The original password is "888888".

A. Connect

Setup DCS Server or Backup Server IP configuration.

Also can select:

♦

Auto reconnect

♦

Switch to backup server when break

B. Network

Setup network configuration.

C. Password

Setup password.

D. Language

Select the operation language.

E. Other

Setup loudspeaker volume, luminance and calibrate.

After a certain period of operation, the touch point on the

touch screen may not be accurate, clicking on the

"Calibration" will calibrate the touch screen.

After entering the calibration interface, please click the

crossing cursor.

Summary of Contents for hcs-8300
































































































































































































































































Search results

Summary of Contents for hcs-8300

Reviews:

Related manuals for hcs-8300

Brands by name

Popular brands

Taiden hcs-8300, Installation And Operation Manual

Search results

Summary of Contents for hcs-8300

Reviews:

Related manuals for hcs-8300

Brands by name

Popular brands