manualshive.com logo in svg

Taiden hcs-8300, Installation And Operation Manual

Share
Download
Taiden hcs-8300 Installation And Operation Manual Download Page 152

 

 

139 

5.1.2 Connection between the CMU/EMU and the contribution units 

HCS-8300 

series 

congress units (except 

HCS-8338/8348 series) feature a 1.5 m 6P-DIN standard 

plug cable and a 0.6 m  6P-DIN socket cable. 

Contribution units  adopt dedicated 6-Pin cable and are 

daisy-chained,  which makes the installation handy and 

effortless. Connect the 1

st

 unit to the outlet connector of 

the CMU, and following connect the plug of the cable of 

the 2

nd

 unit to the socket of the 1

st

 unit. Proceed one by 

one in a series configuration.The backbone of HCS-8300 

system is formed (as shown in figure 5.1.1). 

HCS-8338  and HCS-8348  series Paperless Multimedia 

Congress Terminal is  designed based on the Gigabit 

Multimedia  Congress Stream technology, all audio and 

video signals are transmitted via a Cat.6 Gigabit network 

cable.  The CMU can be connected to the Gigabit 

network switcher via a Cat.6 Gigabit network cable. For 

connecting the congress terminals to the Gigabit network 

switcher, just connect the “1000M Ethernet” interface of 

a congress terminal to the “Delegate” interface of the 

Gigabit network switcher  with a Cat.6 Gigabit network 

cable. For the connection between congress  terminals, 

just connect the free “1000M Ethernet” interfaces of the 

adjoining congress terminals. 

 

 

Figure 5.1.1  Congress main unit connecting to HCS-8315 contribution units 

 

Summary of Contents for hcs-8300
































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands