Taiden hcs-8300 Installation And Operation Manual Download Page 81

Page: 81 / 255

3.3.3.3 Video display

The HCS-8335 series economical multimedia terminal

is equipped with a 10” TFT LCD with 1280

800

high-resolution. It supports high definition digital video

(SDI) display corresponding with the standard

CEA-861. Video signal transmitted on a high quality

coaxial-cable, such as RG-6 or SYV-75 and the length

of each cable is no more than 50 m.

3.3.3.4 External microphone

An external microphone can be connected to the

external microphone jack of the congress terminal. The

external microphone shall have a Ø 3.5 mm plug, as in

the following figure:

Functions and indications:

2 Suspend/Ground

3 Ground

3.3.3.5 External earphone

An external earphone can be connected to the external

earphone jack of the congress terminal. Its volume can

be adjusted by the earphone volume control button.

The external earphone shall have a Ø 3.5 mm plug, as

in the following figure:

Functions and indications:

1 Left stereo channel signal

2 Right stereo channel signal

3 Power ground/Shield

Summary of Contents for hcs-8300
































































































































































































































































Search results

Summary of Contents for hcs-8300

Reviews:

Related manuals for hcs-8300

Brands by name

Popular brands

Taiden hcs-8300, Installation And Operation Manual

Search results

Summary of Contents for hcs-8300

Reviews:

Related manuals for hcs-8300

Brands by name

Popular brands