Taiden hcs-8300 Installation And Operation Manual Download Page 156

Page: 156 / 255

143

5.1.5 Connection between HCS-8300 PMCS and central control system

TAIDEN

intelligent central control system is an advanced

comprehensive control system. It can link together

various devices, hardware and environment equipment

from different manufacturers. The central control system

can operate the conferencing devices through wired

Ethernet or wireless bidirectional communication by

wired/wireless touch panel. Features include power

controlling, environment light adjustment and on-off,

electric curtain or projector screen open-close and on-off,

system PA volume controlling and controlling various

electric devices, such as DVD, VCR, TV, projector, etc.

RS-232C or RS-485 interfaces are available. Remote

controlling, even from distant places, can be achieved

through LAN or internet.

TAIDEN

HCS-6100 intelligent central control system and

TAIDEN

HCS-8300 PMCS can be joined together

seamlessly. In addition to standard functions of a normal

central touch panel control system, it can also control:



Switch on/off microphone of congress unit;



Control video camera;

If using

TAIDEN

intelligent central control system touch

panel to control congress units, ID of each congress unit

should be known.

The connection of HCS-8300 PMCS and the intelligent

central control system is shown in figure 5.1.5.

Figure 5.1.5 HCS-8300M congress system main unit connecting to central control system

Summary of Contents for hcs-8300
































































































































































































































































Search results

Summary of Contents for hcs-8300

Reviews:

Brands by name

Popular brands

Taiden hcs-8300, Installation And Operation Manual

Search results

Summary of Contents for hcs-8300

Reviews:

Brands by name

Popular brands