Taiden hcs-8300 Installation And Operation Manual Download Page 37

Page: 37 / 255

2.1.3.3 To fiber device

HCS-8300MAU/FS and HCS-8300MAD/FS/20 have a

pair of fiber interfaces, and can be connected to

HCS-4100MA/FS/50, HCS-8300 series CMU/EMU,

audio input unit, audio output unit, and two distant

meeting rooms (distance can reach tens of kilometers)

can be combined as one meeting room. The

connection between the fiber interfaces is shown in the

following figure:

Figure 2.1.8 Connecting between CMU and EMU via

optical fiber cable

2.1.3.4 To CobraNet/Dante device

CobraNet and Dante are both real-time transmission

standard for transmitting digital audio and control data.

HCS-8300MAU/FS has a pair of CobraNet interfaces,

HCS-8300MAD/FS/20 has a pair of Dante interfaces,

and can be connected to CobraNet/Dante devices

through Cat.5 cable.

2.1.3.5 Connecting to AES/EBU standard digital

audio devices

The full name of AES/EBU is Audio Engineering

Society/European Broadcast Union, and has now

become a popular standard of professional digital

audio. AES/EBU is a serial bit transmission protocol to

transmit digital audio data based on single twist pair.

HCS-8300MAU/FS and HCS-8300MAD/FS/20 both

have one set of AES IN and AES OUT interface, and

can connect to AES/EBU compatible digital audio

devices via XLR 3-cord shielded cable.

Summary of Contents for hcs-8300
































































































































































































































































Search results

Summary of Contents for hcs-8300

Reviews:

Brands by name

Popular brands

Taiden hcs-8300, Installation And Operation Manual

Search results

Summary of Contents for hcs-8300

Reviews:

Brands by name

Popular brands