manualshive.com logo in svg

Taiden hcs-8300, Installation And Operation Manual

Share
Download
Taiden hcs-8300 Installation And Operation Manual Download Page 212

 

 

199 

 

After  calibration,  click any place of the touch screen to 

save current setting and return to configuration interface. 

If there is no operation within 30 seconds after calibration, 

it will return to configuration interface automatically. 

 

 

Motor speed 

Adjust the motor speed by pressing the “

” or the 

“

” button. Press the “Auto Adjust” button to adjust the 

motor speed automatically. 

 

 

 

Test Tone Test 

When test tone test is started by operator through DCS 

software, the following interface was actived. The test 

tone test can be controlled by HCS-8301  series digital 

audio mixer. Include test tone Frequency, Amplitude, 

Mute and End Test. 

 

 

Summary of Contents for hcs-8300
































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands