manualshive.com logo in svg

Taiden hcs-8300, Installation And Operation Manual

Share
Download
Taiden hcs-8300 Installation And Operation Manual Download Page 26

 

 

13 

4. E-ink nameplate 

TAIDEN has pioneered the use of E-ink nameplate with 

the latest E-ink technology in the industry, and it is built 

in the new 

generation 

paperless 

multimedia 

conference terminals like HCS-8338 and HCS-8348 

series. The effect of E-ink nameplate is close to the 

paper, it is soft, flicker-free, glare-free, and will not 

cause eye fatigue, the content can be permanent 

display without power, visual angle close to 180 

degrees, low power consumption and energy saving. 

 

 

Figure 1.1.11  HCS-8338-NP/HCS-8348-NP Series New 

Generation Paperless Multimedia Congress Terminal 

Congress Terminal 

 

5.  Duplicate and backup connection via  “Closed 

Loop - Daisy Chain” connection topology 

For important meetings, especially those which 

consider connection reliability as their leading point, 

HCS-8300 Series New Generation Paperless 

Multimedia Congress System  adopts advanced 

“Closed Loop -  Daisy Chain” connection topology, 

connecting the last unit in the loop back to the 

Congress Main Unit. Therefore, any Congress Unit in 

the loop has two connection paths to the Congress 

Main Unit. As a result, breakdown or replacement of a 

Congress Unit and connection failure of a cable will not 

influence other Congress Units. As such the system 

features the advantages of a daisy chain connection 

system with its simpleness of cabling as well as the 

improvement of the system reliability by means of 

duplicate and backup connection functions. 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for hcs-8300
































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands