Taiden hcs-8300 Installation And Operation Manual Download Page 153

Page: 153 / 255

140

5.1.3 Connection between HCS-8300 PMCS and automatic video tracking system

HCS-8300 PMCS can be connected to an automatic

video tracking system. For video tracking purposes, the

application software is used to make camera presets for

every congress unit. If the congress unit is switched on,

video tracking system will automatically find the

appropriate preset and focus on the speaker. The view of

the speaker will be displayed on large screen or other

display devices. The automatic video tracking system is

compatible with several kinds of video signals and

operates automatic video switching. The video tracking

system is composed of video switcher, button board and

high-speed dome camera.

Use a RS-485 cable and connect HCS-8300 Main unit

(port “TO VIDEO SWITCHER”) to the corresponding port

at the rear panel of the video switcher as shown in the

following figure:

Figure 5.1.2 HCS-8300M congress main unit connecting to automatic video tracking system

Summary of Contents for hcs-8300
































































































































































































































































Search results

Summary of Contents for hcs-8300

Reviews:

Related manuals for hcs-8300

Brands by name

Popular brands

Taiden hcs-8300, Installation And Operation Manual

Search results

Summary of Contents for hcs-8300

Reviews:

Related manuals for hcs-8300

Brands by name

Popular brands