Taiden hcs-8300 Installation And Operation Manual Download Page 199

Page: 199 / 255

186

6.6 HCS-8300KMX

HCS-8300KMX is designed based on the Gigabit

Multimedia Congress Stream technology, and is used to

connect the congress main unit, the HCS-8338 and

HCS-8348 series Paperless Multimedia Congress

Terminals, the video server, external Ethernet switches,

etc.

6.6.1 Functions and instructions

Front panel

Rear panel

Figure 6.6.1 HCS-8300kMX Congress Gigabit Network Switcher

Figure 6.6.1:

1. Power indicating light

2. RJ45 interface (ETHERNET)



Connecting to the server.

3. RJ45 interface (TO MAIN UNIT)



Connecting to the CMU.

4. RJ45 interface (DELEGATE)



Connecting to HCS-8338 and HCS-8348 series

Paperless Multimedia Congress Terminals, the

quantity of congress terminals connected to each

port is unlimited.

5. 6P-DIN interface (TO MAIN UNIT)



For power supply from the CMU.

6. 2P aviation plug base (DC24V - 33V)



For power supply from the Power Supply Unit.

6.6.2 Connection

8×RJ45 standard ports for connection with the congress

main unit, the HCS-8338 and HCS-8348 series

Paperless Multimedia Congress Terminals, the video

server, external Ethernet switches, etc. The quantity of

congress terminals connected to each port is unlimited if

the HCS-8338 and HCS-8348 series Paperless

Multimedia Congress Terminals are “daisy chained”. The

power for the unit is provided by the CMU or the Power

Supply Unit.

Connection refers to figure 1.1.4b HCS-8338 Series

Paperless Multimedia Congress System connection

diagram (dual main unit hot spare + “Closed Loop –

Daisy Chain” connection).

Summary of Contents for hcs-8300
































































































































































































































































Search results

Summary of Contents for hcs-8300

Reviews:

Brands by name

Popular brands

Taiden hcs-8300, Installation And Operation Manual

Search results

Summary of Contents for hcs-8300

Reviews:

Brands by name

Popular brands