Taiden hcs-8300 Installation And Operation Manual Download Page 92

Page: 92 / 255



Brightness

Set brightness of LCD screen.



Standby

Stand by HCS-8336 or not.



Language

Set the OSD menu language.



Aspect Ratio

Set aspect ratio for HCS-8336 SDI monitor. Three

items for choice: Full, 16:9, and 4:3.

B. “Unit Setting”

Unit setting includes Select booth number and

Loudspeaker Volume. Select a sub-menu, the item will

be highlight with blue; when pressing the “Menu” key,

the item will be highlight with red. It means that the

content of this item can be modified by pressing “+” key

or “-” key and then press the “Menu” key again to

confirm.



Select booth number

Set booth number for the HCS-8336 SDI monitor.



0: used in the venue;



Others: used in booths.



Loudspeaker Volume

Adjust the built-in loudspeaker volume for the

HCS-8336 SDI monitor, range: -30 dB – 0 dB.



Mutes automatically to suppress howling

when the microphone of the interpreter unit in

the same booth is active;



When the booth number is 0, loudspeaker

volume can be adjusted by the master

volume control knob on the main unit or by

TAIDEN conference management software

Summary of Contents for hcs-8300
































































































































































































































































Search results

Summary of Contents for hcs-8300

Reviews:

Related manuals for hcs-8300

Brands by name

Popular brands

Taiden hcs-8300, Installation And Operation Manual

Search results

Summary of Contents for hcs-8300

Reviews:

Related manuals for hcs-8300

Brands by name

Popular brands