manualshive.com logo in svg

Siemens RUGGEDCOM ROX II, User Manual

Introducing the Siemens RUGGEDCOM ROX II, a robust and reliable networking solution designed for extreme environments. Enhance your understanding of its advanced features and functionalities with our comprehensive User Manual. Download the user manual for free from manualshive.com and explore the full potential of this exceptional product.

Share
Download
background image

RUGGEDCOM ROX II

CLI User Guide

Chapter 12

Tunneling and VPNs

Deleting a VLAN

387

3. Type 

commit

 and press 

Enter

 to save the changes, or type 

revert

 and press 

Enter

 to abort.

Section 12.4.6.3

Deleting a VLAN

To delete a VLAN for a static or dynamic L2TPv3 tunnel session, do the following:
1. Make sure the CLI is in Configuration mode.
2. Delete the tunnel by typing:

no

 tunnel l2tpv3 [ static | dynamic ] tunnel 

tunnel-name

 session 

tunnel-session

 vlan 

vid

Where:
•

tunnel-name

 is the name of the tunnel

•

tunnel-session

 is the name of the tunnel session

•

vid

 is the VLAN ID for the routable logical interface

3. Type 

commit

 and press 

Enter

 to save the changes, or type 

revert

 and press 

Enter

 to abort.

Section 12.5

Managing GOOSE Tunnels

The GOOSE tunnel feature provides the capability to bridge GOOSE frames over a Wide Area Network (WAN).
GOOSE tunnels provide the following features:
• GOOSE traffic is bridged over the WAN via UDP/IP.
• One GOOSE traffic source can be mapped to multiple remote router Ethernet interfaces in mesh fashion.
• To reduce bandwidth consumption, GOOSE daemons may be located at each of the 

legs

 and at the center of a

star network. The centrally located daemon will accept GOOSE packets and re-distribute them.

• Statistics report availability of remote GOOSE daemons, packet counts and Round Trip Time (RTT) for each

remote daemon.

• When the Virtual Router Redundancy Protocol (VRRP) is employed, GOOSE transport is improved by sending

redundant GOOSE packets from each VRRP gateway.

• You can enable GOOSE forwarding by configuring a generic Layer 2 tunnel. When configured, the device listens

for GOOSE packets on one VLAN and forwards them to another VLAN.

The GOOSE protocol is supported by the Layer 2 Tunnel Daemon. The daemon listens to configured Ethernet

interfaces and to the network itself (i.e. for tunnel connections from other daemon instances) on a configurable

UDP port.
The Media Access Control (MAC) destination address of frames received from Ethernet is inspected in order to

determine which GOOSE group they are in. The frames are then encapsulated in network headers and forwarded

(with MAC source and destination addresses intact) to the network as GOOSE packets.
IEC61850 recommends that the MAC destination address should be in the range 01:0c:cd:01:00:00 to

01:0c:cd:01:01:ff.
GOOSE packets received from the network are stripped of their network headers and forwarded to Ethernet

ports configured for the same multicast address. The forwarded frames contain the MAC source address or the

originating device, and not that of the transmitting interface. The VLAN used will be that programmed locally for

Summary of Contents for RUGGEDCOM ROX II































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RUGGEDCOM ROX II

IBM E12 Quick Reference Manual preview
E12
Brand: IBM Pages: 4
NavigateWorx NR300 User Manual preview
NR300
Brand: NavigateWorx Pages: 71
Draytek VigorIPPBX 2820 Series Quick Start Manual preview
VigorIPPBX 2820 Series
Brand: Draytek Pages: 29
D-Link DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network... User Manual preview
DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network...
Brand: D-Link Pages: 53
REXROTH efc series Instruction Manual preview
efc series
Brand: REXROTH Pages: 68
Hirschmann OCTOPUS 5TX-EEC Description And Operating Instructions preview
OCTOPUS 5TX-EEC
Brand: Hirschmann Pages: 6
Wintech TDS510USB Plus Installation Manual preview
TDS510USB Plus
Brand: Wintech Pages: 21
UNA AUTOMATION DIFRA Installation Manual preview
DIFRA
Brand: UNA AUTOMATION Pages: 20
Advantech MIC-730AI User Manual preview
MIC-730AI
Brand: Advantech Pages: 36
IDT Digital Encoder Plus User Manual preview
Digital Encoder Plus
Brand: IDT Pages: 98
ZALMAN CNPS5700D-Cu User Manual preview
CNPS5700D-Cu
Brand: ZALMAN Pages: 7
Patton IPLink 2603 Series User Manual preview
IPLink 2603 Series
Brand: Patton Pages: 120
Patton electronics IPLink 2803 Specifications preview
IPLink 2803
Brand: Patton electronics Pages: 2
Ubiquiti EdgeRouter 12 Quick Start Manual preview
EdgeRouter 12
Brand: Ubiquiti Pages: 23
ZALMAN RESERATOR2 Installation And Operational Manual preview
RESERATOR2
Brand: ZALMAN Pages: 18
Procool SP480 Series Instructions preview
SP480 Series
Brand: Procool Pages: 2
ZyXEL Communications POE-12 Specifications preview
POE-12
Brand: ZyXEL Communications Pages: 2
IMC Networks Wireless Outdoor Bridge XI-1500-IH Quick Installation Manual preview
Wireless Outdoor Bridge XI-1500-IH
Brand: IMC Networks Pages: 13

Brands by name

Popular brands

Load more brands