![background image](http://html1.mh-extra.com/html/ryobi/rdp102l/rdp102l_manual_1504970014.webp)
SPEED AND WIRING
The speed of the product is not constant and decreases
under a load or with lower voltage. For voltage, the wiring
in a shop is as important as the motor’s horsepower
rating. A line intended only for lights cannot properly
carry a power tool motor. Wire that is heavy enough for
a short distance will be too light for a greater distance. A
line that can support one power tool may not be able to
support two or three tools.
GROUNDING INSTRUCTIONS
In the event of a malfunction or breakdown, grounding
provides a path of least resistance for electric current
to reduce the risk of electric shock. The product is
equipped with an electric cord having an equipment-
grounding conductor and a grounding plug. The plug
must be plugged into a matching outlet that is properly
installed and grounded in accordance with all local
codes and ordinances.
Do not modify the plug provided. If it will not
fi
t the outlet,
have the proper outlet installed by a quali
fi
ed electrician.
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. The
conductor with insulation having an outer surface that
is green with or without yellow stripes is the equipment-
grounding conductor. If repair or replacement of the
electric cord or plug is necessary, do not connect the
equipment-grounding conductor to a live terminal.
Repair or replace a damaged or worn cord immediately.
RECOMMENDED ACCESSORIES
WARNING
Use only accessories recommend for this drill press.
Follow instructions that accompany accessories. Use
of improper accessories may cause hazards.
■
Drill bits
■
Hold-down clamps
■
Drill press vices
WARNING
Use only accessories designed for this drill press to
avoid injury from thrown broken parts or workpieces.
Do not use any accessory unless you have completely
read the instruction or operator’s manual for that
accessory.
CARTON CONTENTS
UNPACKING AND CHECKING CONTENTS
WARNING
If any part is missing or damaged, do not plug the drill
press in until the missing or damaged part is replaced,
and assembly is complete.
Carefully unpack the drill press and all its parts, and
compare against the list below.
To protect the drill press from moisture, a protective
coating has been applied to the machined surfaces.
Remove this coating with a soft cloth moistened with
kerosene or WD-40.
WARNING
To avoid
fi
re or toxic reaction, never use gasoline,
naphtha, acetone, lacquer thinner or similar highly
volatile solvents to clean the drill press.
Apply a coat of paste wax to the table, column and
machined surfaces of base to prevent rust. Wipe all
parts thoroughly with a clean dry cloth.
Item
Description
Quantity
1
Head assembly
1
2
Table
1
3
Base
1
4
Rack
1
5
Column assembly
1
6
Rack ring
1
7
Feed handles
3
8
Worm gear
1
9
Table lock handle
1
10
Table crank handle
1
11
Hex bolts
3
12
Chuck
1
13
Chuck key
1
14
4 mm hex key
1
15
3 mm hex key
1
14
Original Instructions
Summary of Contents for RDP102L
