DUROFIX RI60165 Information Manual Download | Manualshive

Page: 1 / 15

background image

-1

RI60165, RI60165A1, RI60166-3,
RI60166, RI60166A1,RI60166A2
BRUSHLESS IMPACT WRENCH

PRODUCT INFORMATION MANUAL

THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY,
OPERATION, MAINTENANCE AND STORAGE OF THIS PRODUCT.

DO NOT

ATTEMPT TO OPERATE THE TOOL UNTIL YOU HAVE READ AND

UNDERSTOOD  ALL  INSTRUCTIONS  AND  SAFETY  RULES  CONTAINED  IN  THIS
MANUAL. FAILURE TO COMPLY MAY RESULT IN ACCIDENTS INVOLVING FIRE,
ELECTRIC  SHOCK,  OR  SERIOUS  PERSONAL  INJURY.  SAVE  THIS  OWNER’S
MANUAL  FOR  FUTURE  REFERENCE  AND  REVIEW  IT  FREQUENTLY  FOR  SAFE

OPERATION.

Original Instructions

1
2
3
...
»

Summary of Contents for RI60165
















Reviews:

No comments

Related manuals for RI60165

GDS Professional 24

Brand: Bosch Pages: 175

Brand: Sthor Pages: 44

Brand: RODCRAFT Pages: 62

Brand: USAG Pages: 56

Brand: Paoli Pages: 64

Brand: Cembre Pages: 38

Brand: Makita Pages: 68

Brand: AEG Pages: 16

Brand: AEG Pages: 96

Brand: Hitachi Pages: 24

Brand: SATA Pages: 20

Brand: Graphite Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands