manualshive.com logo in svg

Proximus Forum 500 Series, Mounting And Commissioning Manual

The Proximus Forum 500 Series is a cutting-edge communication device that revolutionizes business collaborations. Enhance your productivity with this sleek and efficient technology. To maximize its potential, don't forget to download the free user manual from manualshive.com. Discover the endless possibilities this device has to offer.

Share
Download
background image

Forum Gateway 560 Installation

100

6.

Switch the Forum Gateway 560 on. To do so, reconnect the power supply 
unit with the mains supply (if you are powering the system with two 
power supply units, connect the second unit as well).

The Forum Gateway 560 will now start up and all modules (interface 
cards) will be re-initialised.

7.

Observe the module LEDs during start-up of the Forum Gateway 560. 
Information on indicators can be found in the chapter 

Forum Gateway 560 

Modules

 starting on page 115.

Backplane

The BPV+1-12 backplane of a Forum Gateway 560 supplies the modules 
installed in the 1-12 frame with the required power and system signals. The 
backplane is also used to provide access to the PCM highway (for transmitting 
utility data), the LAN (for exchanging signalling data) and to the system clock 
circuits.

The backplane has vertically arranged sockets for the backplane plugs of the 
modules:

●

The Forum 550 Power Supply units and the Forum 550 Card main proc-
essor central control module are each connected by means of a 96-pin 
spring contact strip. 

●

The interface modules are each connected by means of a 48-pin spring 
contact strip. 

Should you need to exchange the backplane, proceed as follows: 

DANGER!

Hazardous voltages inside the device!

1.

Unplug all of the mains cables of the Forum Gateway 560 to disconnect 
the device from the mains supply.

Refer to 

Notes on Disconnecting the Mains Supply

 starting on page 95.

2.

Uninstall all modules and power supply units from the 1-12 frame (see 

Installing Modules

 starting on page 94).

3.

Remove the screws on the backplane (see arrows in the illustration 

Backplane screws

). Carefully remove the backplane from the 1-12 frame, 

pulling it out of the frame towards the front.

Summary of Contents for Forum 500 Series





























































































































































































































































































































































Reviews:

No comments

Related manuals for Forum 500 Series

Yealink MVC Series Quick Start Manual preview
MVC Series
Brand: Yealink Pages: 6
Yealink MeetingSpace VC800 Deployment Manual preview
MeetingSpace VC800
Brand: Yealink Pages: 6
Yealink MeetingEye 400 Quick Start Manual preview
MeetingEye 400
Brand: Yealink Pages: 16
Yealink One Talk CP960 Quick Manual preview
One Talk CP960
Brand: Yealink Pages: 4
Yealink One Talk CP960 Quick Start Manual preview
One Talk CP960
Brand: Yealink Pages: 20
Yealink VC400 Administrator'S Manual preview
VC400
Brand: Yealink Pages: 299
Yealink VC210 Teams Edition Quick Start Manual preview
VC210 Teams Edition
Brand: Yealink Pages: 12
Yealink CP860 SERIES Quick User Manual preview
CP860 SERIES
Brand: Yealink Pages: 5
Yealink VC400 Quick Start Manual preview
VC400
Brand: Yealink Pages: 16
Yealink MeetingBar A20 User Manual preview
MeetingBar A20
Brand: Yealink Pages: 30
Yealink MeetingSpace VC200 Quick Start Manual preview
MeetingSpace VC200
Brand: Yealink Pages: 8
Yealink MVC Series: MVC800 Quick Start Manual preview
MVC Series: MVC800
Brand: Yealink Pages: 16
Yealink CP930W Telesystem Quick Reference Manual preview
CP930W Telesystem
Brand: Yealink Pages: 2
Yealink VC110 Quick Start Manual preview
VC110
Brand: Yealink Pages: 16
K&G GROEP NANO MARINE Installation And Operation Manual preview
NANO MARINE
Brand: K&G GROEP Pages: 27
Audipack VCL-1UP Installation Manual preview
VCL-1UP
Brand: Audipack Pages: 12
EIS kb sound Series Installation Manual preview
kb sound Series
Brand: EIS Pages: 2
Vestil BOL-R Series Instruction Manual preview
BOL-R Series
Brand: Vestil Pages: 6

Brands by name

Popular brands

Load more brands