manualshive.com logo in svg

Proximus Forum 500 Series, Mounting And Commissioning Manual

Share
Download
Proximus Forum 500 Series Mounting And Commissioning Manual Download Page 130

Forum Gateway 560 Modules

128

●

The maximum range is 1000 m.

Pin assignment

For information on the U

pn

 interface pin assignment, refer to 

U

pn

 Ports

 

starting on page 109.

Indicators

There are four LEDs on the front of the Forum 550 Card 8 digital extensions 
interface card.

Forum 550 Card 8 digital extensions: LEDs

The LEDs indicate the following: 

Operational information

The Forum 550 Card 8 digital extensions interface card can be exchanged 
during operation. However, the slot must first be deactivated in the 

LED 1: 

Constantly yellow

At least one connection established 
through the interface card is active.

LED 2:

Constantly green

The interface card is operational; the slot 
has been activated (flickering is normal).

Flashing yellow

The interface card is ready, but the slot 
has not been activated or the interface 
card has not been configured yet.

Constantly red

New software is being loaded onto the 
interface card. If the LED lights up red for 
an extended period of time, there may 
be a fault.

LED 3:

–

Not used

LED 4:

–

Not used

UPN 1

UPN 2

MS+UPN2-8

1
2

3
4

Summary of Contents for Forum 500 Series





























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands