Proximus Forum 500 Series Mounting And Commissioning Manual Download Page 92 | Manualshive

Page: 92 / 348

background image

Forum Gateway 560 Installation

90

Notes on the Mains Supply

A Forum Gateway 560 may be connected only to mains sockets with a
protective earth conductor.

Install a Forum Gateway 560 only near easily accessible, wall-mounted
mains sockets.

Always use a dedicated circuit with 10 A protection to supply the 19" frame
(1-12 frame).

If a Forum Gateway 560 is being powered by two Forum 550 Power Supply
units, each of the two units must be plugged into its own mains socket.

It is

not permissible

to use

multiway mains strips

to connect more than one

power supply unit of a Forum Gateway 560 or a Forum Gateway 560 and
other devices to the same mains supply together.

The mains cables of the Forum 550 Power Supply units must have ferrite
rings fitted. The mains cables are factory-fitted with ferrite rings.

Mains cable with ferrite ring

Install an overvoltage protection device.

Notes on EMC and Earthing

Please note:

MOS modules:
Observe the regulations regarding modules and packaging
carrying the MOS trademark!

Use earthing wrist straps connected to the appropriate points on the frame
(see C in the illustration

Forum Gateway 560: 1-12 frame mounting points

The mains socket’s protective earth conductor and the telephone earth line
must be connected to one reference point for potential equalisation. This is
normally the Forum Gateway 560 housing.

«
...
90
91
92
93
94
...
»

Summary of Contents for Forum 500 Series





























































































































































































































































































































































Reviews:

No comments

Related manuals for Forum 500 Series

Brand: Fagor Pages: 10

Brand: Fagor Pages: 172

Brand: Fagor Pages: 112

OneFlow OFTWH-R

Brand: Watts Pages: 8

Passport Conference 2 Series

Brand: Fender Pages: 20

Brand: Skov Pages: 68

Brand: Subpac Pages: 15

Brand: Nakamichi Pages: 11

Brand: ATEN Pages: 176

Brand: WesAudio Pages: 65

Brand: Audio Control Pages: 36

Brand: HK Audio Pages: 105

Brand: Fuslon Pages: 14

Brand: Roadstar Pages: 16

Brand: Adcom Pages: 16

Stealthbox SB-CAN-G2MVX3D/10TW3

Brand: JL Audio Pages: 6

Brand: RCA Pages: 20

Brand: Pioneer Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands