manualshive.com logo in svg

Proximus Forum 500 Series, Mounting And Commissioning Manual

Share
Download
Proximus Forum 500 Series Mounting And Commissioning Manual Download Page 41

Additional Memory Module

Installation

39

Please note:

After breaking off the release flaps, the edges where they 
broke off must be deburred.

Additional Memory Module

An additional memory module can be installed in the Forum 5004/5008/
5012 communications system to increase recording capacities. This memory 
module provides a recording capacity of 24 hours. The enhanced memory can 
be used for recordings and voiceboxes.

WARNING!

Only the Proximus service technician is authorized to install 
the memory module. 

DANGER!

Dangerous voltage in device! You may not open the 
housing yourself. Pull the plug out of the power socket 
before opening the service panel and connecting any 
lines/terminals! Failure to do so may cause danger to life 
from electric shock!

CAUTION!

Static charges can damage the Forum 5004/
5008/5012 communications system electronic 
components. Please make sure that you discharge 
yourself and your tools before and during any installation 
work on the Forum 5004/5008/5012 communications 
system. 

The memory module is installed on the call server mainboard of the 
Forum 5004/5008/5012 communications system. It must be plugged and 
screwed (A) according to the following illustration. Earthing is led by screwing. 

Summary of Contents for Forum 500 Series





























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands