manualshive.com logo in svg

Proximus Forum 500 Series, Mounting And Commissioning Manual

The Proximus Forum 500 Series is a cutting-edge communication device that revolutionizes business collaborations. Enhance your productivity with this sleek and efficient technology. To maximize its potential, don't forget to download the free user manual from manualshive.com. Discover the endless possibilities this device has to offer.

Share
Download
background image

SIP Telephony

Voice over IP (VoIP)

175

After restart, the logged out SIP system telephone will show a login page. A 
user can enter his call number and his user PIN. If a device entry with this call 
number exists and has the same device type, the login procedure continues. If 
the device entry is currently active on another device, the associated remote 
SIP system telephone will be logged out automatically and will show a login 
page on its part. The now logged in SIP system telephone starts and will get 
its configuration from the newly assigned device entry.

Note:

When adding the device entry, it is also possible to activate the 

Logged out

 option. 

SIP Entrance Intercom Systems

You can operate IP-based entrance intercom systems (EIS) in the 
Forum 5004/5008/5012. The “SIP” protocol is used for signalling. As far as 
the Forum 5004/5008/5012 communications system is concerned, an SIP 
entrance intercom system (SIP EIS) is an SIP telephone produced by another 
manufacturer that is used for the audio connection to the door. You can find 
information about installing a SIP EIS in the relevant documentation provided 
by the manufacture. 

Technical Requirements

To operate an SIP EIS, the communications system must be equipped to 
operate SIP standard terminals.

●

A licence is required to operate SIP standard terminals. Please see the 
explanations in the 

Licence assignment

 starting on page 166 section. 

●

The integrated relays that are used to grant access through the door are 
controlled using DTMF. DTMF signalling as per RFC4733 is commonly used 
for this purpose. The VoIP profile of a SIP EIS should therefore include the 

DTMF (RFC 4733) (event)

 codec. 

Configuring SIP EISs

The configuration of a SIP EIS consists of two configuration sections:

●

Setup of the SIP EIS in the Forum 5004/5008/5012 communications 
system (system configuration). This process generates the SIP parameters 
that are necessary for registration of the SIP EIS in the Forum 5004/
5008/5012 communications system.

Summary of Contents for Forum 500 Series





























































































































































































































































































































































Reviews:

No comments

Related manuals for Forum 500 Series

NEC UNIVERGE SL2100 Networking Manual preview
UNIVERGE SL2100
Brand: NEC Pages: 196
NEC UNIVERGE SL2100 Hardware Manual preview
UNIVERGE SL2100
Brand: NEC Pages: 174
NEC ElectraElite IPK General Description Manual preview
ElectraElite IPK
Brand: NEC Pages: 151
iHome IA100 Instruction Manual preview
IA100
Brand: iHome Pages: 17
Grundig CIRFLEXX UMS 4100 Service Manual preview
CIRFLEXX UMS 4100
Brand: Grundig Pages: 38
Thermo Scientific CC58114PBC Installation And Operation Manual preview
CC58114PBC
Brand: Thermo Scientific Pages: 68
Weber Markoprint iJET Operating Manual preview
Markoprint iJET
Brand: Weber Pages: 127
RAM AUF200 User Manual preview
AUF200
Brand: RAM Pages: 22
Parker 2003-CB-00 Technical Manual preview
2003-CB-00
Brand: Parker Pages: 47
Greenheck 474754 Installation, Operation And Maintenance Manual preview
474754
Brand: Greenheck Pages: 16
Grandstream Networks UCM6304 Quick Installation Manual preview
UCM6304
Brand: Grandstream Networks Pages: 20
SMA DATA MANAGER L Operating Manual preview
DATA MANAGER L
Brand: SMA Pages: 64
Imesa MCM 2500 Use, Installation And Maintenance Instructions preview
MCM 2500
Brand: Imesa Pages: 33
Boss Rebel ATV22CB User Manual preview
Rebel ATV22CB
Brand: Boss Pages: 2
Kenwood KRF-V7300D Instruction Manual preview
KRF-V7300D
Brand: Kenwood Pages: 72
Kenwood KRF-V7300D Service Manual preview
KRF-V7300D
Brand: Kenwood Pages: 84
Kenwood KRF-V6200D Instruction Manual preview
KRF-V6200D
Brand: Kenwood Pages: 44
Kenwood KRF-V6400D Instruction Manual preview
KRF-V6400D
Brand: Kenwood Pages: 48

Brands by name

Popular brands

Load more brands