manualshive.com logo in svg

Proximus Forum 500 Series, Mounting And Commissioning Manual

The Proximus Forum 500 Series is a cutting-edge communication device that revolutionizes business collaborations. Enhance your productivity with this sleek and efficient technology. To maximize its potential, don't forget to download the free user manual from manualshive.com. Discover the endless possibilities this device has to offer.

Share
Download
background image

Forum Gateway 560 Installation

99

Installing a Power Supply Unit

Depending on the number of installed modules (interface cards), either one or 
two power supplies are required (see A and B in the illustration 

Forum Gateway 560: 1-12 frame slots

 on page 94): 

●

The power supply unit for group 1 (A) must always be installed. It supplies 
the central control module and the interface cards in slots 1 - 6.

●

The power supply unit for group 2 (B) is required if interface cards are to 
be installed in slots 7 - 12.

If you want to deinstall the second power supply unit or exchange a defective 
one, proceed as follows:

DANGER!

Hazardous voltages inside the device!

1.

Unplug all of the mains cables of the Forum Gateway 560 to disconnect 
the device from the mains supply. 

Power supply units must not be installed if the Forum Gateway 560 is 
switched on! Refer to 

Notes on Disconnecting the Mains Supply

 starting on 

page 95. 

2.

Unpack the power supply unit. 

CAUTION!

Static charge can damage electronic devices. 
Observe the regulations regarding electrostati-
cally sensitive components.

3.

Carefully push the power supply unit into the corresponding slot (see also 
the illustration 

Forum Gateway 560: 1-12 frame slots

 on page 94). Seen 

from the front, the mains inlet socket should be on the bottom right.

Ensure that the backplane plug of the power supply unit is securely 
plugged into the socket on the backplane.

4.

Refit the screws to secure the power supply in the 1-12 frame.

5.

Install further interface cards if required (see also 

Installing Interface Cards

 

starting on page 97).

Summary of Contents for Forum 500 Series





























































































































































































































































































































































Reviews:

No comments

Related manuals for Forum 500 Series

Bang & Olufsen BeoSound 5 User Manual preview
BeoSound 5
Brand: Bang & Olufsen Pages: 20
Bang & Olufsen BeoSound 5 Manual preview
BeoSound 5
Brand: Bang & Olufsen Pages: 24
Bang & Olufsen BeoSound Ouverture User Manual preview
BeoSound Ouverture
Brand: Bang & Olufsen Pages: 44
Eclipse E-iSERV CD3200 Operation Manual preview
E-iSERV CD3200
Brand: Eclipse Pages: 5
Eclipse CD7100 Operation Manual preview
CD7100
Brand: Eclipse Pages: 21
JBL HTPS-400 Owner'S Manual preview
HTPS-400
Brand: JBL Pages: 8
Beyerdynamic MCW-D 200 Operating Instructions Manual preview
MCW-D 200
Brand: Beyerdynamic Pages: 112
Daewoo MC-5911SC Service Manual preview
MC-5911SC
Brand: Daewoo Pages: 21
Grandstream Networks GAC2570 User Manual preview
GAC2570
Brand: Grandstream Networks Pages: 177
Talk To Me Technologies eyespeak zuvo 12-D User Manual preview
eyespeak zuvo 12-D
Brand: Talk To Me Technologies Pages: 28
Polycom RealPresence Group 500 systems System Setup Sheet preview
RealPresence Group 500 systems
Brand: Polycom Pages: 2
btsr IS3 Operating Manual preview
IS3
Brand: btsr Pages: 71
Boss Audio Systems MR100 User Manual preview
MR100
Brand: Boss Audio Systems Pages: 4
Polycom SoundStation 2W User And Administrator Manual preview
SoundStation 2W
Brand: Polycom Pages: 46
Blaupunkt MS6BK Owner'S Manual preview
MS6BK
Brand: Blaupunkt Pages: 97
Blaupunkt MC200BT Owner'S Manual preview
MC200BT
Brand: Blaupunkt Pages: 112
Contacta IL-K300 Installation & User Manual preview
IL-K300
Brand: Contacta Pages: 12
Sharp XL-35H Quick Start Manual preview
XL-35H
Brand: Sharp Pages: 4

Brands by name

Popular brands

Load more brands