manualshive.com logo in svg

Proximus Forum 500 Series, Mounting And Commissioning Manual

Share
Download
Proximus Forum 500 Series Mounting And Commissioning Manual Download Page 96

Forum Gateway 560 Installation

94

Installing Modules

Forum Gateway 560: 1-12 frame slots

Slots

A Forum Gateway 560 1-12 frame can house up to:

●

2 power  supply  units

●

1 control  module

●

12 interface cards (trunk or subscriber modules) split into 2 separate 
groups.

The following slots are provided for installing these modules: 

Legend

A

Slot for group 1 power supply unit

B

Slot for group 2 power supply unit

0

Slot for central control module

C

Slots for group 1 interface cards (slots 1 - 6) 

D

Slots for group 2 interface cards (slots 7 - 12)

A

D (7-12)

C (1-6)

0

B

Summary of Contents for Forum 500 Series





























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands