Oracle X7-8 Service Manual Download Page 160

Page: 160 / 308

Servicing CPU Module (CMOD) Components (FRU)

Prepare the server for operation.

See

“Returning the Server to Operation” on page 237

Servicing CPU Module (CMOD) Components (FRU)

This section includes information and procedures for servicing CMODs and CMOD

components:

■

“CMOD Slot Locations and Numbering” on page 160

■

“Remove a CMOD” on page 162

■

“Install the CMOD Cover” on page 166

■

“Install a CMOD” on page 167

■

“Servicing DIMMs” on page 182

Caution -

CMODs should be removed and replaced only by authorized Oracle Service

personnel.

Caution -

Component damage. CMOD components are extremely sensitive to electrostatic

discharge. To protect components from damage, always use an anti static mat and wrist strap.

See

“Performing Electrostatic Discharge and Static Prevention Measures” on page 98

For component serviceability, locations, and designations, see

“Identifying

Components” on page 24

. See

“CPU Module (CMOD) Overview” on page 28

CMOD Slot Locations and Numbering

CPU module slots are arranged in a single row and are designated from left to right as, CMOD

0–CMOD 7. The CMOD slots are accessible from the front of the server by removing the FMs

and frames.

The server is available with four CMODs or eight CMODs. Four-CMOD systems have CMODs

in CMOD 0–CMOD 3, and empty slots in CMOD 4–CMOD 7.

For more information, see

“CPU Module (CMOD) Overview” on page 28

160

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands

Oracle X7-8, Service Manual

Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands