manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 219

Remove the FIM

■

“Remove the FIM” on page 219

■

“Install the FIM” on page 221

Caution - 

FIMs should be removed and replaced only by authorized Oracle Service personnel.

For component serviceability, locations, and designations, see 

“Identifying

Components” on page 24

.

Remove the FIM

Access this component directly from the front of the server. Remove the FIM when you need to

replace it.

1.

Prepare the server for cold service.

This is a cold-service component. Power down the system and disconnect the AC power cables

from the server before performing this procedure.
See 

“Preparing the Server for Component Replacement” on page 101

.

2.

Remove the top power supply (PS3). See 

“Remove a Power

Supply” on page 141

.

Servicing Components

219

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands