manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 22

About Controls and Connectors

The following table lists the server back panel components:

Call

Out

Component

Link

1

SMOD1 System B SYSTEM SUMMARY status indicator LEDs:

■ System Locate Button/LED: White
■ Chassis Fault-Service Required: Amber
■ System B OK: Green
■ SP OK Service Processor: Green

“System Module (SMOD)

Overview” on page 34

“System Module (SMOD)

Indicators” on page 65

“Servicing System Module (SMOD) Components

(FRU)” on page 195

2

SMOD1 System B NET MGT

Oracle ILOM (SP) network management 10/100/1000BASE-T port

“System Module (SMOD)

Overview” on page 34

“Servicing System Module (SMOD) Components

(FRU)” on page 195

3

SMOD1 System B SER MGT

The SMOD1 System B serial management port service processor SER MGT

port uses an RJ-45 cable and terminal (or emulator) to provide access to the

Oracle ILOM command-line interface (CLI).

“System Module (SMOD)

Overview” on page 34

“Servicing System Module (SMOD) Components

(FRU)” on page 195

4

SMOD1 System B USB

The SMOD1 System B USB 3.0 port supports hot-plugging of devices.

“System Module (SMOD)

Overview” on page 34

“Servicing System Module (SMOD) Components

(FRU)” on page 195

22

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands