manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 66

Troubleshooting Using Status Indicators

found on the front indicator module (FIM), including reset switches and indicators for SMOD

components.

The following figure shows the back panel SMOD indicators:

Call

Out

Status LED or Button

Icon and Color

Description

1

Locate button/LED

White

When activated remotely, lighting the SMOD Locate LED helps you find the server

and SMOD0 System A or SMOD1 System B. Press this button to prove physical

presence at the server chassis, as required for some Oracle ILOM tasks.

■ Off – Server is operating normally,
■ Fast blink – Use Oracle ILOM to activate this LED to enable you to locate a

system quicklly and easily.

See 

“Managing the Locate Button/LED” on page 120

.

2

Fault-Service Required

Amber

Indicates a fault state in SMOD:

■ Off – SMOD is operating normally,
■ Steady On – A fault is present in SMOD.

Other amber (fault) indicators might also be lit, which can help you isolate the fault to

a particular subsystem.

See 

“Troubleshooting Using Status Indicators” on page 59

.

3

System OK

Green

Indicates the operational state of the SMOD:

■ Off – AC power is not present or the Oracle ILOM boot is not complete.
■ Flashing – SMOD is booting.
■ Steady On – OS has booted, power is on and chassis SMOD is running.

66

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands