Oracle X7-8 Service Manual Download Page 194

Page: 194 / 308

Install a DIMM

This action forces the DIMM into the slot and causes the two slot levers to rise and lock the

DIMM in the slot.

Verify that the DIMM sits evenly in the slot and is locked.

Both levers should be in their fully closed and vertical position. In this position the levers lock

the DIMM in the slot.

Install the CMOD cover.

See

“Install the CMOD Cover” on page 166

10.

(Optional) Use Oracle ILOM to clear server DDR4 DIMM faults.

DDR4 DIMM faults are automatically cleared after a new DIMM has been installed. If you

need to manually clear DDR4 DIMM faults, refer to the Oracle Integrated Lights Out Manager

(ILOM) 4.0 Documentation Library at

http://www.oracle.com/goto/ilom/docs

Note -

If you want to move a faulty DDR4 DIMM to a new DIMM socket or re-seat a DIMM

for troubleshooting, you must first manually clear the associated DIMM fault. Otherwise, the

DIMM fault might follow the DIMM to the new socket location or reoccur on the current socket

location, causing a false DIMM fault condition.

Related Information

■

“Install a CMOD” on page 167

194

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands

Oracle X7-8, Service Manual

Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands