manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 166

Install the CMOD Cover

4.

Lift the CMOD top cover away from the CMOD.

Install the CMOD Cover

When removing or installing the CMOD cover, always maintain component serviceability

requirements with regard to static protection.

1.

“Remove a CMOD” on page 162

.

2.

To install the cover, position it over the CMOD chassis with the green button at

the front.

3.

Set the cover on the chassis, leaving a gap of approximately 1 inch (25 mm)

between the lead edge of the cover and the front of the CMOD.

4.

Ensure that the edges of the cover encapsulate the edges of the chassis, and

that the pins in the cover are aligned with the slots in the chassis sidewall.

166

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands