manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 162

Remove a CMOD

■

Both fan frames must be installed.

For the dual 4-socket server configuration:

■

System module 0 (SMOD0) System A and SMOD1 System B must be installed.

■

CPU modules (CMODs) must be installed in slots 0-7.

■

DPCC slots 0-3 and DPCC slots 4-7 must be installed and are active.

■

All eight fan modules (FMs) must be installed. All FMs are active in the dual 4-socket

configuration.

■

Both fan frames must be installed.

For the 8-socket server configuration:

■

System module 0 (SMOD0) System A and SMOD1 System B must be installed.

■

CPU modules (CMODs) must be installed in slots 0-7.

■

DPCC slots 0-7 must be installed and are active.

■

All eight fan modules (FMs) must be installed and all FMs are active.

■

Both fan frames must be installed.

Note - 

During Oracle Server X7-8 reconfiguration, administrators will need to manually clear

all existing faults before an 4-socket to 8-socket mode change.

Remove a CMOD

You need to remove the CMOD to service it or its internal components.

1.

Prepare the server for service. Choose one of the following methods:

■

Prepare the server for warm service.

■

Prepare the server for cold service.

See 

“Preparing the Server for Component Replacement” on page 101

.

2.

Identify which group of fan modules (left or right) to remove to access the

CMOD.

For CMODs 0-3 access remove the left FM group. For CMODs 4-7 access remove the right FM

group. In a four-CMOD configured server, remove the left FM group.

162

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands