manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 199

Install an SMOD

5.

Align the SMOD in the slot.

6.

Slide the SMOD into the slot until it stops.

This leaves the SMOD protruding slightly from the back of the server. Do not attempt push the

SMOD in beyond this point.

7.

To install the SMOD, simultaneously rotate both handles up until they lock into

place.

Caution - 

Pinch point. When operating the lever, keep your fingers clear of the back side and

hinged end of the lever.

This action draws the SMOD inward engaging the SMOD connectors with the connectors on

the server midplane.

8.

Connect the cables to the SMOD.

9.

Prepare the server for operation. See 

“Returning the Server to

Operation” on page 237

.

Related Information

■

“System Module (SMOD) Overview” on page 34

Servicing Components

199

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands