Oracle X7-8 Service Manual Download Page 44

Page: 44 / 308

System Module (SMOD) Overview

Call

Out

Component

Description

Links

Storage Drives

Left facing back of chassis: SMOD1 HDD/SSD

slots 0 through 3:

Right facing back of chassis: SMOD0 HDD/SSD

slots 0 through 3:

Top row : 3, 1

Bottom row: 2, 0

“Storage Drive Locations and

Numbering” on page 124

“Storage Drive

Indicators” on page 69

System Module

A (SMOD0)

SMOD system A internal components can only be

accessed by removing the SMOD from the server

back panel.

“System Module (SMOD)

Overview” on page 34

“System Module (SMOD)

Indicators” on page 65

System Module

B (SMOD1)

SMOD system B internal components can only be

accessed by removing the SMOD from the server

back panel.

“System Module (SMOD)

Overview” on page 34

“System Module (SMOD)

Indicators” on page 65

Dual PCIe card

carrier (DPCC)

bay

The DPCC bay contains eight DPCCs and up to 16

PCIe cards.

“PCI Devices

Subsystem” on page 88

“Dual PCIe Card Carrier (DPCC)

Indicators” on page 70

AC power block

The AC power block has four AC power inlet

connectors, two for each SMOD. The power block

is not a removable component.

“Power

Subsystem” on page 83

“AC Power Block Inlet

Indicators” on page 71

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands

Oracle X7-8, Service Manual

Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands