manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 158

Install a DPCC

10.

Clear any related component faults. For more information see 

“Clear Hardware

Fault Messages (Oracle ILOM)” on page 53

.

Related Information

■

“Install a DPCC” on page 158

Install a DPCC

Perform this procedure as part of a PCIe card replacement or configuration. To remove a

DPCC, see 

“Remove a DPCC” on page 151

.

Before You Begin

Obtain a stylus for activating recessed buttons.

1.

Prepare the server for service. Choose one of the following methods:

■

Prepare the server for hot service.

■

Prepare the server for cold service.

See 

“Preparing the Server for Component Replacement” on page 101

.

2.

Ensure the top of the DPCC is closed and secured and the lever on the front of

the DPCC is in its fully open position.

3.

Align the DPCC with the vacant slot.

158

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands