manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 249

Configure TPM Support

Note - 

TPM enables you to administer the TPM security hardware in your server. For additional

information about implementing this feature, refer to the Windows Trusted Platform Module

Management documentation provided by your operating system or third-party software vendor.

1.

Access the BIOS Setup Utility menus.

See 

“Access BIOS Setup Utility Menus” on page 241

.

2.

In the BIOS Setup Utility menus, navigate to the Advanced Menu.

3.

On the Advanced Menu screen, select 

Trusted Computing 2.0

.

4.

On the Trusted Computing 2.0 Configuration screen, select 

Security TPM Device

Support

 and press Enter. Do one of the following:

■

Select 

Disable

 to disable Security TPM Device Support.

■

Select 

Enable

 to enable Security TPM Device Support.

Setting Up BIOS Configuration Parameters

249

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands