manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 30

CPU Module (CMOD) Overview

Call

Out

Description

1

CMOD Fault Remind button

2

Circuit Charge Status indicator

3

12 DIMM slots arranged in two groups of six

4

DIMM slot fault indicators (12, one for each slot)

5

Processor Heatsink Module (PHM)

6

CPU fault indicator

For component serviceability, locations, and designations, see 

“Identifying

Components” on page 24

.

CMOD Processor

Each CMOD contains one Intel Xeon vx processor (shelf 4) processor.

■

Four CPU modules installed in slots 0 through 3

■

Eight CPU modules installed in slots 0 through 7

■

24 cores per-socket (224 total)

The Processor Heatsink Module (PHM) is a three part module that is installed above the socket

assembly:

30

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands