manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 125

Remove a Storage Drive

Call Out

Description

5

HDD 0 SMOD1

6

HDD 1 SMOD1

7

HDD 2 SMOD1

8

HDD 3 SMOD1

Storage Drive Population Rules

When populating the storage drive slots, use the following rules:
1. Every slot in the storage drive bay must contain either a storage drive or a drive filler panel.
2. Sort disks by capacity and technology (HDD and SSD) and install in this order:

a. Install the HDDs first, starting with the smallest capacity in the drive slots in ascending

slot order (0, 1, etc.).

b. Install larger HDDs in increasing capacity and into storage slots increasing in number.
c. Install SSDs into remaining storage slots increasing in number.

For component serviceability, locations, and designations, see 

“Identifying

Components” on page 24

.

Remove a Storage Drive

For storage drive information, see 

“Storage Drive Locations and Numbering” on page 124

.

1.

Prepare the server for service. Choose one of the following methods:

■

Prepare the server for hot service.

■

Prepare the server for cold service.

See 

“Preparing the Server for Component Replacement” on page 101

.

2.

Identify the storage drive by its position, designation, and the indicators on its

front panel.

Access this component directly from the back of the server.
For storage drive information, see 

“Storage Drive Locations and Numbering” on page 124

.

For example, look for the blue steady on Ready to Remove indicator or the amber steady on

Fault-Service Required LED. See 

“About Controls and Connectors” on page 72

.

Servicing Components

125

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands