manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 248

Configure TPM Support

3.

In the Please Select Boot Device dialog box, select the boot device according to

the operating system you elected to use, and then press Enter.

4.

Follow the on-screen instructions to install the operating system from the

selected boot device.

Related Information

■

“Accessing the BIOS Setup Utility” on page 239

■

“BIOS Setup Utility Menu Options” on page 269

■

“BIOS Key Mappings” on page 240

■

“Exit BIOS Setup Utility” on page 267

Configure TPM Support

If you intend to use the Trusted Platform Module (TPM) feature set, you must configure the

server to support this feature. TPM support is enabled by default on Oracle Server X7-8.

Perform the procedure in this section to disable or enable TPM support.

248

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands