manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 182

Install a Processor

-> 

set /SYS/MB/P0 clear_fault_action=true

For example:

-> 

set /SYS/MB/P0 clear_fault_action=true

Are you sure you want to clear /SYS/MB/P0 (y/n)? 

y

Set ‘clear_fault_action’ to ‘true’

Alternatively, to clear all known faults in the server, log into the Oracle Solaris OS and

issue the 

fmadm repair

 command, or log into the Oracle ILOM service processor from

the Oracle ILOM Fault Management Shell and issue the 

fmadm repair

 command. For

more information about how to use the Oracle ILOM Fault Management Shell and

supported commands, see the 

Oracle ILOM User's Guide for System Monitoring and

Diagnostics Firmware Release 4.0.x

 in the Oracle Integrated Lights Out Manager (ILOM)

4.0 Documentation Library at 

http://www.oracle.com/goto/ilom/docs

.

Related Information

■

“Identify and Remove a Faulty Processor” on page 171

Servicing DIMMs

This section describes how to service memory modules (DIMMs). DIMMs are field-replaceable

units (FRUs) that require you to power off the server. For more information about FRUs, see

“Illustrated Parts Breakdown” on page 24

 and 

“Customer-Replaceable Units” on page 26

.

The Oracle Server X7-8 supports 64-GB quad-rank (QR) Load-Reduced DIMMs (LRDIMMs)

and 32-GB dual-rank (DR) and 16-GB DR Registered DIMMs (RDIMMs).

Caution - 

These procedures require that you handle components that are sensitive to

electrostatic discharge. This sensitivity can cause the components to fail. To avoid damage,

ensure that you follow antistatic practices as described in 

“Performing Electrostatic Discharge

and Static Prevention Measures” on page 98

.

Caution - 

DIMMs should be removed and replaced only by authorized Oracle Service

personnel.

Caution - 

Ensure that all power is removed from the server before removing or installing

DIMMs, or damage to the DIMMs might occur. You must disconnect all power cables from the

system before performing these procedures.

182

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands