manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 123

Servicing Components

This section includes the following removal and installation procedures for customer-

replaceable and field-replaceable components in the Oracle Server X7-8.

Section Description

Link

Remove and install server storage drives.

“Servicing Storage Drives (CRU)” on page 123

Remove and install fan modules (FM).

“Servicing Fan Modules (CRU) and Fan Frames

(CRU)” on page 129

Remove and install power supplies (PS).

“Servicing Power Supplies (CRU)” on page 138

Remove and install PCIe cards and dual

PCIe card carriers (DPCC).

“Servicing PCIe Cards and Carriers (CRU)” on page 148

Remove and install CPU modules (CMOD)

including CMOD processor and memory

components.

“Servicing CPU Module (CMOD) Components

(FRU)” on page 160

Removing and installing SMOD assembly

and components.

“Servicing System Module (SMOD) Components

(FRU)” on page 195

Remove and install the front indicator panel

(FIM).

“Servicing the Front Indicator Module (FRU)” on page 218

Replacing the midplane assembly.

“Replace the Midplane Assembly” on page 226

Upgrade server from four to eight CMODs.

“Upgrade the Server from Four to Eight CMODs

(FRU)” on page 223

For component serviceability, locations, and designations, see 

“Identifying

Components” on page 24

.

Servicing Storage Drives (CRU)

■

“Storage Drive Locations and Numbering” on page 124

.

■

“Remove a Storage Drive” on page 125

■

“Install a Storage Drive” on page 127

Servicing Components

123

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands