Oracle X7-8 Service Manual Download Page 28

Page: 28 / 308

CPU Module (CMOD) Overview

FRU

Description

Replacement Instructions

Storage drive

backplanes

Cold-serviceable

Provide power and communications connectors for storage drives

located in SMODs.

“Servicing Storage Drives (CRU)” on page 123

Battery

Cold-serviceable

3V Lithium Coin Cell Battery that powers the CMOS BIOS and

real-time clock located in SMODs.

“Servicing System Module (SMOD) Components

(FRU)” on page 195

SAS cables

Cold-serviceable

Provide signals between the SMOD front disk backplane and the

Oracle Storage 12Gb SAS PCIe RAID HBA, Internal 16-Port.

“Servicing the SAS Cable” on page 211

Internal HBA

card

Cold-serviceable

Located in SMODs, the Oracle Storage 12Gb SAS PCIe RAID

HBA, Internal 16-Port manages SAS storage drives.

“Servicing the Host Bus Adapter (HBA)

Card” on page 200

Front indicator

module (FIM)

Contains push-button circuitry and LED indicators that are

displayed on the chassis bezel.

“Servicing the Front Indicator Module

(FRU)” on page 218

Midplane

Cold-serviceable

Internal midplane/busbar assembly in the chassis.

“Replace the Midplane Assembly” on page 226

Related Information

■

“Customer-Replaceable Units” on page 26

■

“Illustrated Parts Breakdown” on page 24

CPU Module (CMOD) Overview

CPU modules (CMODs) contain one processor (CPU) and the system memory. CMODs supply

power to the fan modules and the DPCCs.

These topics provide information about server CPU modules (CMODs), CMOD 0-7

configuration options, and the internal layout of CMOD components:

■

“CMOD Components” on page 29

■

“CMOD Processor” on page 30

■

“CMOD Memory” on page 31

■

“CMOD and Fan Module Power” on page 33

CMODs are internal warm or cold-service components, front panel accessible. To access the

CMODs, you must remove the fan modules and the fan frames.

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands

Oracle X7-8, Service Manual

Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands