Oracle X7-8 Service Manual Download Page 60

Page: 60 / 308

Troubleshooting Using Status Indicators

■

“Front Indicator Module (FIM) Panel” on page 60

■

“Power Supply (PS) Indicators” on page 64

■

“Fan Module (FM) Indicators” on page 63

■

“Storage Drive Indicators” on page 69

■

“System Module (SMOD) Indicators” on page 65

■

“Dual PCIe Card Carrier (DPCC) Indicators” on page 70

■

“AC Power Block Inlet Indicators” on page 71

Related Information

■

“Controls and Indicators” on page 72

■

“Identifying Components” on page 24

Front Indicator Module (FIM) Panel

The front indicator module (FIM) panel is located at the top left corner of the server (as viewed

from the front of the server). Use buttons to control the server. Use indicators to determine

server status. The FIM provides controls and indicators for three system configurations.

■

Single 4-socket: The FIM provides controls and indicators for System A (SMOD0) only.

System B (SMOD1) buttons and indicators are not operational.

■

Dual 4-socket: The FIM provides separate controls and indicators for System A (SMOD0)

and System B (SMOD1).

■

8-socket: The FIM provides controls and indicators for System A (SMOD0) and System B

CMODs 4-7. Other System B (SMOD1) buttons and indicators are not operational.

The following figure shows FIM buttons and indicators.

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands

Oracle X7-8, Service Manual

Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands