manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 72

Troubleshooting Using Status Indicators

Call

Out

Status LED or Button

Icon and

Color

Description

3

AC 2

~AC

AC 2 (SMOD0) System A

4

AC 3

~AC

AC 3 (SMOD0) System A

Do not attach power cables to the power supplies until you finish connecting the data cables to

the server. The server goes into Standby power mode, and the Oracle ILOM service processor

initializes when the AC power cables are connected to the power source. System messages

might be lost after 60 seconds if the server is not connected to a terminal, PC, or workstation.

About Controls and Connectors

The following sections describe the controls, indicators, connectors, and drives located on the

front and back panels.

■

“Front Indicator Module (FIM) Panel” on page 60

■

“Power Supply (PS) Indicators” on page 64

■

“Fan Module (FM) Indicators” on page 63

■

“Storage Drive Indicators” on page 69

■

“System Module (SMOD) Indicators” on page 65

■

“Dual PCIe Card Carrier (DPCC) Indicators” on page 70

■

“AC Power Block Inlet Indicators” on page 71

■

“Controls and Indicators” on page 72

Controls and Indicators

Use the buttons, switches, and status indicators on the front and back of the server, server

management software, and Oracle ILOM to troubleshoot the server:

■

Server Boot Process and Normal Operating State Indicators

■

Locate Button/LED Indicator On

■

Over Temperature Condition

■

PSU Fault

■

Memory Fault

■

CPU Fault

■

Fan Module Fault

■

SP Fault

72

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands