manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 197

Install an SMOD

4.

To remove the SMOD, hold the SMOD by its sides and slide it out of the server.

Caution - 

The SMOD is heavy. Be prepared to hold it firmly when it is clear of the slot.

Related Information

■

“Install an SMOD” on page 197

Install an SMOD

Perform the following tasks before installing the SMOD.

Before You Begin

■

“Remove an SMOD” on page 195

.

■

Perform this procedure after servicing internal SMOD components, such as the HBA card,

ESM, internal USB ports, and system battery.
For component serviceability, locations, and designations, see 

“Identifying

Components” on page 24

.

1.

Prepare the server for cold service.

Servicing Components

197

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands