Oracle X7-8 Service Manual Download Page 148

Page: 148 / 308

Servicing PCIe Cards and Carriers (CRU)

Call

Out

Status LED or Button

Icon and

Color

Description

Power Supply OK LED (green)

Green

Indicates the functional state of the power supply:

■ Off – PS is disconnected
■ Steady On – PS is powered on and functionaing

normally. When this LED is lit, the AC OK LED

is also lit.

Note -

Oracle ILOM signals a fault on any installed

power supply that is not connected to an AC power

source, since it might indicate a loss of redundancy.

AC OK LED (green)

~AC

Green

Indicates the operational state of the power supply:

■ Off – PS is not connected to an AC power

source.

■ Steady On – PS is connected to a properly rated

AC power source.

Prepare the server for operation.

See

“Identifying Components” on page 24

Servicing PCIe Cards and Carriers (CRU)

Refer to your PCIe card documentation for complete software and cabling information about

your card.

Caution -

Customers should not use the procedures in this section to service the Oracle Storage

12 Gb SAS PCIe RAID HBA, Internal card that is located in SMODs. The Oracle Storage 12

Gb SAS PCIe RAID HBA, Internal cards are field-replaceable units (FRUs) and should be

serviced only by authorized Oracle Service personnel.

Caution -

These procedures require that you handle components that are sensitive to

electrostatic discharge. This sensitivity can cause the components to fail. To avoid damage,

ensure that you follow antistatic practices as described in

“Performing Electrostatic Discharge

and Static Prevention Measures” on page 98

Caution -

Ensure that all power is removed from the server before removing or installing

PCIe cards. You must disconnect all power cables from the system before performing these

procedures.

148

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands

Oracle X7-8, Service Manual

Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands