manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 208

Replace the ESM Extension Cable

Push it straight down into position..

7.

Attach the ESM connector to the ESM extension cable [2].

8.

Install the SMOD. See 

“Install an SMOD” on page 197

.

9.

Prepare the server for operation. See 

“Returning the Server to

Operation” on page 237

.

Replace the ESM Extension Cable

1.

Prepare the server for cold service.

This is a cold-service component. Power down the system and disconnect the AC power cables

from the server before performing this procedure.
See 

“Preparing the Server for Component Replacement” on page 101

.

2.

Remove the SMOD. See 

“Remove an SMOD” on page 195

.

3.

Rotate the SMOD 180 degrees so the back (connector) side is facing toward you.

208

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands