Oracle X7-8 Service Manual Download Page 177

Page: 177 / 308

Install a Processor

Install a Processor

Caution -

Be careful not to touch the processor socket pins. The processor socket pins are very

fragile. A light touch can bend the processor socket pins beyond repair.

Attach an antistatic wrist strap to your wrist, and then to a metal area on the

chassis.

See

“Performing Electrostatic Discharge and Static Prevention Measures” on page 98

Ensure that the replacement processor is identical to the failed processor that

you removed.

For a description of the processors that are supported by the server, see

“Product

Description” on page 17

Prepare the new processor for installation.

Use the syringe (supplied with the new or replacement processor) to apply

approximately 0.3 cc of thermal grease to the center of the underside of the

heatsink [1].

Distribute the thermal grease over the square heatsink-to-processor contact

area using a flat-edged tool [2].

Note -

Ensure that you spread thermal grease evenly on the contact areas.

Install the new processor.

Servicing Components

177

Summary of Contents for X7-8





















































































































































































































































































































Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands

Oracle X7-8, Service Manual

Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands