Oracle X7-8 Service Manual Download Page 193

Page: 193 / 308

Install a DIMM

Locate the DIMM slot.

Install a DIMM.

Ensure that the ejector tabs are in the open position.

Align the notch in the replacement DIMM with the connector key in the

connector socket.

The notch ensures that the DIMM is oriented correctly.

To align the DIMM in the slot, ensure that the notch on the DIMM connector

lines up with the key in the DIMM slot.

Push the DDR4 DIMM into the connector socket until the ejector tabs lock

the DIMM in place.

If the DIMM does not easily seat into the connector socket, verify that the notch in the

DIMM is aligned with the connector key in the connector socket. If the notch is not

aligned, damage to the DIMM might occur.

To install the DIMM in the slot, simultaneously press down on both edges of the

DIMM.

Servicing Components

193

Summary of Contents for X7-8





















































































































































































































































































































Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands

Oracle X7-8, Service Manual

Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands