Oracle X7-8 Service Manual Download Page 76

Page: 76 / 308

Troubleshooting Using Status Indicators

Fan Module Fault

For a server with a fan module fault, the server amber Fault-Service Required LEDs (front and

back) and an amber Fault-Service Required LED on a fan module are on steady. The front and

back green On Standby, server OK indicator and the green SP indicator are on steady.

Service Processor Fault

For a server with an SP (service processor) fault, the server amber Fault-Service Required

LEDs (front and back) are on steady. The front and back System OK indicators and the SP OK

indicator are off.

Front Panel Lamp Test

To perform a lamp test of all front panel indicators, press the Locate Button/LED button three

times within a five second period. All the front and back indicators light up and remain on

steady for 15 seconds (see

“Unison Steady On” on page 80

Back Panel Pinhole Switches

This section shows the location of the back panel pinhole switches.

Call

Out

Button

Icon

Description

Non-maskable Interrupt (NMI)

button (recessed) SMOD0

Do not press. This button is used by Oracle Service personnel only and

requires a stylus.

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands

Oracle X7-8, Service Manual

Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands