manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 38

System Module (SMOD) Overview

Call

Out

Description

10

NET 0-3 10 GbE Network ports labeled NET0, NET1, NET2, and NET3. Network ports, back panel

accessible

11

Service Processor (SP) - concealed location

12

3V Lithium Coin Cell Battery

13

Real time clock battery socket

For component serviceability, locations, and designations, see 

“Identifying

Components” on page 24

.

For replacement procedures, see 

“Servicing System Module (SMOD) Components

(FRU)” on page 195

.

SMOD Motherboard

Each SMOD motherboard contains:

■

Two Storage Drive Backplanes (for externally accessible server storage drives)
Externally accessible server storage drives on the SMOD connect to two storage drive

backplanes mounted on the SMOD motherboard. One SAS cable connects each backplane

to the HBA card that is installed in a riser slot on the underside of the SMOD. Storage drive

backplanes are not removable or replaceable.

■

Service processor (SP)
The system Emulex Pilot 4 service processor (SP) is located on the SMOD motherboard

and is accessible locally and remotely through management ports on the front of the SMOD.

The SP contains Oracle ILOM, an embedded server management tool. The SP is not

removable.

■

System real time clock battery, 3V Lithium Coin Cell Battery

■

Energy storage module (ESM) for the server storage HBA
The Energy Storage Module (ESM) provides backup power for the Oracle Storage 12Gb

SAS PCIe RAID HBA, Internal 16-Port card. The ESM is located in a holder in the top

center of the SMOD. A cable connects the HBA to to the ESM.

■

PCIe riser for the server storage HBA, located on the bottom of the SMOD
The server requires one internal HBA (Oracle Storage 12Gb SAS PCIe RAID HBA,

Internal 16-Port) for the externally-accessible SAS (or SATA) SMOD server storage drives.

The HBA is installed in a riser slot on the underside of the SMOD motherboard and is

connected to the backplanes by two mini-SAS4I connector cables.

38

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands